• Single acting, handed
• Weight up to 450 pounds
• Door width up to 4’

Code

• Single acting, handed
• ANSI/C06041/C06051

Features

• Built in positive dead stop prevents door from swinging past desired opening degree; Specify 85,90,95 or 105 degrees
• Separate valves for closing speed, latch speed and back check
• Available non hold open (N) or selective hold open (S)
• Vertical door adjustment
• Low opening force “PH”

• Single Acting, handed
• Weight up to 350 pounds
• Center arm
• Door sizes up to 4’ X 8’6”

Code

• ANSI/C06021

Features

• Centering arm with adjustment screws in faces of door
• Built in positive dead stop prevents door from swinging past desired • opening degree; Specify 85,90,95 or 105 degrees
• Separate valves for closing speed, latch speed and back check
• Available non hold open (N) or selective hold open (S)
• Vertical door adjustment
• Low opening force “PH”

• Full Mortise and handed

Features

• Not load bearing
• Maintains door alignment
• ¾” Offset standard, 1-1/2” offset special order
• Non-ferrous based material
• Furnished with wood and machine screws

Code

• BHMA/ANSI NO : 07321/C07371

Stocked Product

• Offset hung electric pivot for Power Transfer
• Handed

Features

• Non load- bearing
• Door and jamb portion are factory assembled and cannot be separated
• Stocked 4 wire. special order 6,8,12 wire
• ¾” Offset standard, 1-1/2” offset special order
• Furnished with wood and machine screws

Stocked Product

• Interior Doors, light weight application
• Weight up to 300 pounds
• Door width up to 3’ 6”
• Handed

Features

• Standard 180 top pivot included
• Bottom pivot mortised into floor
• Non-Ferrous Based material
• ¾” offset standard, 1-1/2” offset available special order
• Doors will swing 180 degrees , trim permitting
• Furnished wood and machine screws

Special Order Options

• Available for fire door specify “F”
• For 20 minute label specify “20” suffix
• Available for 1-1/2” offset
• Extended spindles available

Stocked Product

• Interior Doors
• Light weight up to 200 pounds
• Door sizes up to 3’ 6” X 8’ 6”
• Non handed

Features

• Standard top 320 top pivot included
• Bottom pivot mortised into side jamb
• Not allowed on labeled doors
• Available with extended spindles, special order

Code

• BHMA/ANSI NO: C07042 for 127-3/4
• BHMA/ANSI NO C07032 for 128-3/4

Model 128-3/4” same as 127-3/4 except bottom pivot mounts directly to floor

Stocked Product

• Exterior or interior door
• Weight up to 600 pounds
• Door width up to 4’
• Handed

Features

• Standard 180 top pivot included
• M19 intermediate pivot required ( not included)
• ¾” offset , 1-1/2” available special order
• Bottom pivot mounts directly to floor
• Door will swing 180 degrees trim permitting
• Non-Ferrous based material

Code

• BHMA/ANSI NO C07162 and C07202

Special Order Options

• Available for fire door specify “F”
• Available for 20 minute door specify “20”
• 1-1/2” offset available
• Extended spindles available

Stocked Product

• Full Mortise and non handed Features

Features

• Standard top pivot for most offset floor closers
• Oil-impregnated sintered bronze bushing
• Non-Ferrous based material
• ¾” offset
• Furnished with wood and machine screws

Special Order Options

• 1-1/2” offset
• Available for 20 minute door, specify “20”
• Available for fire door specify “F”
• Longer pivot pins available

Stocked Product

• Fully concealed and non handed
• For use with 28 and 30 series closers

Features

• Walking beam-type pivot ½” diameter pivot pin with ¾: engagement
• Oil-impregnated sintered bronze bushing
• Completely concealed when door is closed
• Furnished with wood and machine screws

Special Order Option

• Available with longer thand standard pivot pins

Stocked Product

• Wall Mount with surface wiring

Features

• Total projection 4-1/8”
• Mounting requirements: 1-1/2” deep adapter housing
• Wall must be properly reinforced

Technical information

• Voltage and Current
• 120 VAC,60hz, .020 amp
• 24VAC/DC 60hz, .030 amp
• 12VDC,.040 amp

Code

• ANSI/C00011

Stocked Product

• Wall Mount with concealed Wiring

Features

• Total projection 2-5/8”
• Mounting requirements 2” X4” X 1-3/4” outlet box
• Wall must be properly reinforced and outlet box adequately fastened

Technical information

• Voltage and Current
• 120 VAC,60hz, .020 amp
• 24VAC/DC 60hz, .030 amp
• 12VDC,.040 amp

Code

• ANSI/C00011

Stocked Product